Amavisd-new Revision as of Sunday, 20 December 2015 at 19:56 UTC

For CentOS 6.4, with Amavisd-new 2.8. Assuming you have
ClamAV and SpamAssassin
installed already.

Amavisd-new takes a message from
Postfix, gives it to content checkers like
ClamAV and
SpamAssassin, and hands the message
back to Postfix, which then decides what to do with it (i.e., reject,
keep it in hold, and so on)¹.

I learned a lot about this from this excellent
guide.

Installation

   yum install amavisd-new
   chkconfig amavisd on
   service amavisd start

Setting up the Transport

Unless you changed the defaults, the amavisd daemon will run on
localhost, on port 10024. Configuration is a two-step process.

Transport Messages from Postfix to Amavis

You can ask Postfix to filter a message through whatever you want after
it is queued but before it is delivered to a mailbox. The filter can be
a defined as a pipe, a unix socket, or a TCP/IP socket.

We have the Amavis daemon listening on 127.0.0.1:10024. Let’s tell
Postfix to filter its messages through that TCP/IP socket. In
/etc/postfix/main.cf, add the following:

   content_filter = amavisd:[127.0.0.1]:10024

This is of the form transport:destination. The first part should
correspond to a definition in /etc/postfix/master.cf. Let’s add it:

   amavisd unix    -       -       n       -       2       smtp
       -o smtp_data_done_timeout=1200
       -o smtp_send_xforward_command=yes
       -o disable_dns_lookups=yes
       -o max_use=20

From Amavis back to Postfix

/etc/amavisd.conf contains two options, notify_method and
forward_method. These are the destinations where Amavis will send
notifications and/or messages after processing. The default is an SMTP
host, listening at 127.0.0.1:10025. We can ask Postfix to listen at that
port, thereby letting it get back the messages it sent to Amavis.

This is again the form transport:destination, and must be defined in
/etc/postfix/master.cf.

   127.0.0.1:10025 inet n  -       n       -       -       smtpd
     -o content_filter=
     -o local_recipient_maps=
     -o relay_recipient_maps=
     -o smtpd_restriction_classes=
     -o smtpd_delay_reject=no
     -o smtpd_client_restrictions=permit_mynetworks,reject
     -o smtpd_helo_restrictions=
     -o smtpd_sender_restrictions=
     -o smtpd_recipient_restrictions=permit_mynetworks,reject
     -o smtpd_data_restrictions=reject_unauth_pipelining
     -o smtpd_end_of_data_restrictions=
     -o mynetworks=127.0.0.0/8
     -o smtpd_error_sleep_time=0
     -o smtpd_soft_error_limit=1001
     -o smtpd_hard_error_limit=1000
     -o smtpd_client_connection_count_limit=0
     -o smtpd_client_connection_rate_limit=0
     -o receive_override_options=no_header_body_checks,no_unknown_recipient_checks

Since the usual SMTP server checks were already applied by Postfix, we
set up an innocent/dumb/minimal SMTP ‘server’.

Setting up Amavis

Set the domain and hostnames

   $mydomain = 'example.com';
   $myhostname = 'host.example.com';

Set the home directory

   $MYHOME = '/var/amavis';

Tell Amavis where to look for SpamAssassin data

   $helpers_home = '$MYHOME/db'

Uncomment the notify and forward methods

   $notify_method  = 'smtp:[127.0.0.1]:10025';
   $forward_method = 'smtp:[127.0.0.1]:10025';

Uncomment these lines from /etc/amavisd.conf

   ['ClamAV-clamd',
     \&ask_daemon, ["CONTSCAN {}\n", "/var/run/clamav/clamd.sock"],
     qr/\bOK$/m, qr/\bFOUND$/m,
     qr/^.*?: (?!Infected Archive)(.*) FOUND$/m ]

Miscellanous

Notes

• I was partial to MailScanner,
  another Perl-based interface which looks like a breeze to install.
  However, the Postfix docs say
  it uses “unsupported methods to manipulate Postfix queue files
  directly.” Okay.
• SpamAssassin can be a bit daunting to configure. I found
  [http://www.yrex.com/s
• A big portion of configuration is setting up users for clamav,
  amavis, postfix, etc. for security. I don’t have to worry about this
  given Red Hat packages, but it definitely isn’t something to forget.

Errors

(!)WARN: all primary virus scanners failed, considering backups

This one’s simpler. Make sure that ClamAV is running, and that you’ve
uncommented its definition in /etc/amavisd.conf

Footnotes